| Main Hardware Software Cables/Adapters Forum Contact |
|
Network fre.........ezing |
Post Reply 
|
Page <1 2345> |
| Author | |
Comporder1 
DMX 
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
 Quote Reply
 Posted: 04 Dec 2009 at 9:59pm |
Here is a lag video for you. Also a nice view of the snow fall in south Mississippi! This video is taken from the front porch.
This is the last few seconds of Wizards posted above. Edited by Comporder1 - 04 Dec 2009 at 9:59pm |
|
 |
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 9:18pm |
Carey
|
|
|
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 9:13pm |
|
Ok........ I'll learn to keep my mouth (fingers) shut
It has begun to lag now but only in one spot of the show (only three songs right now) that I have seen. It is at the end of the wizards sequence that I posted above. I watched that particular several times at the beginning of the night and it worked great.
Next... We decided to go grab some food and just as we were getting in the car, the lights went dead. Ran inside and found the dreaded "???(can't remember) has encountered a problem and needs to close. We are sorry for the inconvenience." Restart the scheduler and left for the resturant in the blizzard. (I had to throw that in there. I live in south Mississippi and the snow tonight is very rare!) When we got back, there was a nice layer of snow on the ground so I decided to try to get some video. I grabbed my little pocket cam and went out front. I was able to get one whole song and the battery died! Ha, just my luck. I decided to wait for Wizards to see how it was looking and sure enough, LAG at the end.
Even with the issues.... The snow makes it look BEAUTIFUL!!
 We may have 1 inch on the ground now.EDIT: I wonder if the crash is when the lagging started
 Carey Edited by Comporder1 - 04 Dec 2009 at 9:24pm |
|
|
|
|
deweycooter
Development
Joined: 14 Oct 2007 Location: League City, TX Online Status: Offline Posts: 674 |
Quote Reply
Posted: 04 Dec 2009 at 8:55pm |
|
I didn't see any lagging - but there were missed events. Things are wet here, so that may be partially to blame.
|
|
|
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 6:56pm |
|
Oh!!!! the good news!!
NO LAGGING! YEAH!!
EDIT: SEE BELOW  Edited by Comporder1 - 04 Dec 2009 at 9:20pm |
|
|
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 6:53pm |
|
Ok.... findings as of 6:20pm.
The scheduler you posted reports as v70 not 76 like the sequencer. I assume that doesn't mean anything.
While I was updating and working with the network I updated firmware on everything. This may be the problem I am seeing with missed and sticky channels. see- http://www.aurorashow.com/Forum/forum_posts.asp?TID=930&PID=7563#7563
I posted a clip on youtube with a paticularly bad and visible section on youtube: http://www.youtube.com/watch?v=-WZ2WFbimN4
Here is a screen shot of Aurora: www.williamsonworkshop.com/AuroraScreen.jpg
Here is the dls file: www.williamsonworkshop.com/wizards09.dls Is uses the standard albumn version of Wizards.
I have 8 arches numbered from left to right, 1 thru 8. In the video, you can see 1-8 "leap" on in that order (left to right) and stay on. Then they are supposed to "leap" OFF in this order: 1,8,2,7,3,6,4,5. You can see arch #7 blacks out completly then #5 blacks out.... out of sequence, and not leaping, just black out.
Carey
|
|
|
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 3:27pm |
|
If you select exit, it acts like it wants to close, but just sits there. If you select exit or X again, you get Run-time error '340': Control array element '12'doesn't exist.
|
|
|
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 3:16pm |
|
One small thing I notice right off is that file->exit crashes Aurora
 The red X (top right) will close it gracefully.
|
|
|
|
|
Comporder1
DMX
Joined: 11 Dec 2007 Location: Brookhaven, MS Online Status: Offline Posts: 163 |
Quote Reply
Posted: 04 Dec 2009 at 1:41pm |
|
Got it. I'll update to .69 this afternoon and give the .76 exe a try tonight. Thanks for the assistance. I'll let you know how it goes tomorrow.
Carey
|
|
|
|
|
LightsOnLogan
Admin Group
Joined: 11 Oct 2007 Online Status: Offline Posts: 3187 |
Quote Reply
Posted: 04 Dec 2009 at 1:37pm |
|
Try this for lagging networks (requires 1.0.69 to be installed to function properly) :
http://www.aurorashow.com/downloads/aurora_1_0_76_exe_files.zip Place the files into your Aurora directory and uset the _76 executable to launch Aurora instead of the default files. Do not attempt this with any version other than 69 installed. This is still in beta testing, but given the circumstances (a BIG show stopping issue), I'm also pushing the beta files directly to the public as they develop. |
|
|
|
|
|
|
Post Reply
|
Page <1 2345> |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options