Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

lost a controller

 Post Reply Post Reply Page  12>
Author
Message Reverse Sort Order
  Topic Search Topic Search  Topic Options Topic Options
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Topic: lost a controller
    Posted: 22 Dec 2009 at 1:12pm
Make sure you're using a known good cat5 cable and the right COM port.  Otherwise, I don't know what to suggest - this is probably more appropriate to bring up at the DLight Forums.

If the controller is new this year, you might want to read this thread at D-Light.  Short story - you may need a new PIC.

I have a controller that I think might be in the same boat.


Edited by deweycooter - 22 Dec 2009 at 1:22pm
Back to Top
breakbenj View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 21 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 102
  Quote breakbenj Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 12:23pm
Well I got the light blinking fast but the Firmware updater keeps timing out and never gives me the chance to load the update. I'm so frustrated with it now. I got to go to work so anything You might suggest I will try out tomorow. I still have the same show I had last year without this controller. My singing snowman, candy canes and minitrees will be dark tonight
Jeff

Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 11:18am
Yep - that sounds correct.  But only do the firmware upgrade if you can't set the address via the hardware utility.


Edited by deweycooter - 22 Dec 2009 at 11:18am
Back to Top
breakbenj View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 21 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 102
  Quote breakbenj Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 10:51am
Ok as soon as I get the LED flashing fast I can remove the wire with it controller still powered on and load the firmware the shut down the firmware updater and restart the controller then use the hardware utility right?
Jeff

Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 10:46am
Find the two pins on the board that have JP1 next to them.

Get a piece of insulated wire, strip off 1/4", hold the exposed wire so that it touches both pins as you power up the board - this can be tricky.  And please don't hurt yourself.  As soon as the LED start flashing fast, you can remove the wire.

Here's a pic of a jumper - these are much easier to use because you can just slide it onto the pins: http://ep.yimg.com/ca/I/pcpartscollection_2079_57835564
Back to Top
breakbenj View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 21 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 102
  Quote breakbenj Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 10:44am
I have all the firmware and the updater, Do I really have to use a jumper
Jeff

Back to Top
breakbenj View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 21 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 102
  Quote breakbenj Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 10:39am
I don't have a jumper and wouldn't know how to use it if I did
Jeff

Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 10:29am
First try resetting the address via the Hardware Utility under the Config tab (I think?).  When you start the HW Util, select your com port and make sure the address is ALL.  Make sure you only have this board connected to the computer - otherwise ALL your boards' addresses will get set.  Choose the correct address and click Set.  That should fix it - do a discover units to make sure.

-----------
If that doesn't work - you will need to reload the firmware on the board.  The Firmware Utility can be downloaded (you need to be registered and logged in at d-light).  Also, download the firmware - version 1.17

If I remember the steps correctly:
Make sure ONLY this board is connected.
Unplug the board
Put a jumper across JP1
Power up the board
LED should start flashing fast - this indicates bootloader mode
Start up the Firmware Utility - select your COM port
You'll probably have to set it to FORCE for the controller ID (since it currently doesn't have one)
Once you're connected, you browse to your firmware file and tell it to load.
Once complete - shut down the FW Updater, remove the jumper, and power cycle the board.  Try it with the HW Util and you should be able to discover it.


Edited by deweycooter - 22 Dec 2009 at 10:31am
Back to Top
breakbenj View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 21 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 102
  Quote breakbenj Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 10:13am
Ok Dewey, I hope Your still around. I tried to get the hardware utility to recognize the 4th controller even using the cat5 cables that I know worked for the other controllers to plug straight into the 4th controller and no matter what I tried the hardware utility could not find it but it is finding the 3 others and when I turn all lights on with the hardware utilty the lights that are controlled by the 4th controller light up along wth the rest and testing the 4th controller turns the lights on. Please help me obi wan kanobi!
Jeff

Back to Top
breakbenj View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 21 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 102
  Quote breakbenj Quote  Post ReplyReply Direct Link To This Post Posted: 22 Dec 2009 at 9:00am
Thanks Dewey
Jeff

Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.156 seconds.