Aurora Homepage
Main Hardware Software Cables/Adapters Forum Contact
Forum Home Forum Home > The Vault > I'm New From Spectrum And I Need Help!
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Forum LockedD-light controller template
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
mramsey View Drop Down
Groupie
Groupie
Avatar

Joined: 01 Sep 2008
Location: Rochester, NY
Online Status: Offline
Posts: 41 		  Quote mramsey Quote  Post ReplyReply Direct Link To This Post Topic: D-light controller template
    Posted: 09 Sep 2008 at 6:36pm
I would like to set up a d-light controller template (3 ACX16"s)
I can't seem to do this without adding a song in spectrum to bring over to Aurora (is this the way then change to the song you wish to use). Also, Aurora is  only showing  16 channels in the sequence out of 48.


How have others done it???


Edited by mramsey - 09 Sep 2008 at 6:55pm
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993 		  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 7:02pm
Things to check 
 
Serial Network Config: Is Aurora configured for Network 1 and the proper COM port for your RS485/WiLink
 
Aurora Channel Properties: Make certain each channel is set for the Network Segment you assigned in the Serial Network Config; and that the proper controller number is assigned.
 
You an change the song in Aurora at any time.
 
Aurora will kill duplicate channel name tags (you can't have two channel named GARAGE, for instance or two controllers with the same Device ID)


Edited by LightChristmas - 09 Sep 2008 at 7:04pm

Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341 		  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 8:11pm
I've also found that when I used Virtual Controllers in spectrum, for some reason it created duplicate channels on the same controller.....Among others, I had a Left Window and a Right Window channel in spectrum, when I brought the sequence into Aurora, the Right Window did not get brought in.   I had to go back in spectrum and Sort the controller by channel. (right click feature on the controller), then go channel by channel to make sure they are 1-16 for each controller.      
Chris

www.lightsonsixth.com
Back to Top
mramsey View Drop Down
Groupie
Groupie
Avatar

Joined: 01 Sep 2008
Location: Rochester, NY
Online Status: Offline
Posts: 41 		  Quote mramsey Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 8:17pm
Thanks for the help.
I did stumble across Serial Network Config. and I can output to one controller.
I will also try the other suggestions
Back to Top
mramsey View Drop Down
Groupie
Groupie
Avatar

Joined: 01 Sep 2008
Location: Rochester, NY
Online Status: Offline
Posts: 41 		  Quote mramsey Quote  Post ReplyReply Direct Link To This Post Posted: 10 Sep 2008 at 4:02pm
Originally posted by mramsey

Thanks for the help.
I did stumble across Serial Network Config. and I can output to one controller.
I will also try the other suggestions


I see by naming the channels in one controller 1 - 16
the next controller 1b - 16b, 1c - 16c they all imported fine

thanks

Next I ' ll have to try outputting to all 3 controllers
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.703 seconds.