Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Set Default Intensity Per Channel

 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Sven View Drop Down
Newbie
Newbie


Joined: 29 Oct 2008
Online Status: Offline
Posts: 1
  Quote Sven Quote  Post ReplyReply Direct Link To This Post Topic: Set Default Intensity Per Channel
    Posted: 29 Oct 2008 at 1:03pm
Wanted to ask here before I posted this over in the suggestions...

Let me preface this by saying, for Halloween, I use primarily spotlights. For each light, I aim it and decide what intensity looks the best for each light on it's own. This year I have about 20 different spotlights that turn on and off a lot throughout a 10 minute show.

This is my first year using Aurora, and I haven't really had time to figure out everything about it. Last year was the first year doing this and I used the Spectrum software from D-Light which I don't think was any better at this. So my issue is this, I turn on the lights a lot and each time I turn it on I have to set the intensity using the sliders which can be tedious. I realize I can use the "Recent" settings bar to paste in settings, but each channel is a different intensity and I would like to work chronologically and not go through and set up each channel through the whole sequence.

What I would like to be able to do is have a maximum intensity setting for each channel. For each spotlight I have, I want to be able to tell it that it can't go above a certain percentage intensity. I think what would be easiest to program would be to have a setting on each channel that sets the max intensity (defaults to 100%), and then when playing back the program, use the intensity set in the grid to reflect off that max intensity setting in the channel. So if the max intensity is set to 50% for the channel, and something in that channel is set for 100% intensity in the grid, then it comes out as 50%, and if set to 50% in the grid then it would come out as 25%.

Does this make sense to anyone? Am I just using the software wrong and making everything way more complicated than it needs to be? (I have a tendency to do that.)
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 29 Oct 2008 at 1:38pm

You are using the software properly (per the "normal" methods), but you might not have considered the "grabber" tool ('G' key).  If you have an event of the correct intensity nearby then you can "grab" it and start using it without the tedious sliders.

A 'max' setting has been discussed, however it has not found a specific date in the project plan yet.  There are also some neat tricks planned for the 'B', 'S', E', and 'F' shortcut keys in 2009 (think key combinations for a quick switch of hues and intensities without leaving the grid).  As with all of these feature enhancements, keeping the plumbing simple is key right now (until 1.2 or 1.3)... adding the extra details too soon makes for slower development of the primary features since there is more to break.
Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341
  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 29 Oct 2008 at 1:45pm
I dont think Aurora has that at this particular time because you can set the intensity from the ON function.

If you want , for example, no greater than 50% for 16 channels....you can go into D-light hardware utility and set the controller itself to go no higher than 50%.  Then 50% on Aurora would be 25% on the controller and the lights.  
Chris

www.lightsonsixth.com
Back to Top
jberner View Drop Down
Groupie
Groupie
Avatar

Joined: 12 Sep 2008
Location: Ruther Glen, VA
Online Status: Offline
Posts: 85
  Quote jberner Quote  Post ReplyReply Direct Link To This Post Posted: 29 Oct 2008 at 7:01pm
I have found it easier to leave them at full and just move the forward and back to get the brightness i want at max, and then if i want, I can still cut them to lower intensities.
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.203 seconds.