| Main Hardware Software Cables/Adapters Forum Contact |
|
1.0.32 (beta preview 2 of 1.1) is here! |
Post Reply 
|
Page <12345> |
| Author | |
LightChristmas 
Beta Testers 
Joined: 15 Oct 2007 Location: Equality, IL Online Status: Offline Posts: 993 |
 Quote Reply
 Posted: 29 Nov 2008 at 11:09am |
|
A 640x480 @ 72DPI JPG displays just fine in Vista. Can't see why anything more would be needed. Its not like we're trying to light the Mona Lisa.
|
|
|
|
 |
|
|
ghamma
Newbie 
Joined: 23 Nov 2008 Location: CA Online Status: Offline Posts: 8 |
Quote Reply
Posted: 29 Nov 2008 at 11:35am |
|
Thanks for trying this out. I just created a 640x480 and I get a black box over which the drawn figures show, but no picture is visible.
|
|
|
|
|
LightsOnLogan
Admin Group 
Joined: 11 Oct 2007 Online Status: Offline Posts: 3187 |
Quote Reply
Posted: 30 Nov 2008 at 11:11am |
|
Just out of curiosity, you haven't adjusted the image brightness (sun tool) to zero have you?
|
|
|
|
|
|
|
ghamma
Newbie
Joined: 23 Nov 2008 Location: CA Online Status: Offline Posts: 8 |
Quote Reply
Posted: 30 Nov 2008 at 12:38pm |
|
I didn't adjust the sun tool. Adjusting the sun tool all the way up leaves me a white background for the drawing in playback, half way up a gray background.
|
|
|
|
|
ghamma
Newbie
Joined: 23 Nov 2008 Location: CA Online Status: Offline Posts: 8 |
Quote Reply
Posted: 30 Nov 2008 at 1:18pm |
|
To try for a clean start, I uninstalled the Aurora software, rebooted, installed 1.0.32, and retried an earlier sequence with no change in the preview visualizer display. When I made a new sequence and specified a new background image, I got a very dark gray box in playback visualizer, even with the sun set all the way up. Changing the image to the one I've posted here I got a lighter gray box.
|
|
|
|
|
LightsOnLogan
Admin Group
Joined: 11 Oct 2007 Online Status: Offline Posts: 3187 |
Quote Reply
Posted: 01 Dec 2008 at 3:09pm |
|
Please try another photo just to make sure it isn't something with the photo. Will the default.jpg in the Aurora Sequencer directory display? |
|
|
|
|
|
|
|
ghamma
Newbie
Joined: 23 Nov 2008 Location: CA Online Status: Offline Posts: 8 |
Quote Reply
Posted: 01 Dec 2008 at 10:28pm |
|
I've tried several JPG files with several pixel sizes with the same result. Also the same (no image) with default.jpg.
|
|
|
|
|
MrChristmas2000
Beta Testers
Joined: 06 May 2008 Location: Georgia Online Status: Offline Posts: 344 |
Quote Reply
Posted: 04 Dec 2008 at 7:29am |
|
I have now caught up with my setup and am now back to working on sequencing.
I wanted to update to the 1.0.32 version on my main editing system so I uninstalled ALL previous versions of Aurora. I deleted most of the files in the base Aurora directory.
I then installed the 1.0.32 version.
I needed to move some channels around and re-address most of my channels due to a major addressing scheme change.
I was moving 15 channels from near the bottom to positions nearer the top of the list. I did this one at a time via drag and drop. I then started to re-address channels by clicking on each one. I know there is the blulk channel editor but I have not had much success doing more than a couple of renames at a time without a LONG delay in saving or just crashing. Anyway after I readdressed a few channels Aurora encounters an error and insist on closing. It happened twice.
I knew you would ask but I went back and tested the bulk editor with the following results.
I edited the controller number for 4 channels.
I then did a save.
After repeating this a couple of times on the second save Aurora just closed without any message at all.
I will continue but saving quite often and see if this problem continues. Edited by MrChristmas2000 - 04 Dec 2008 at 7:55am |
|
Holding breath for DMX. |
|
|
|
|
kalifi
Newbie
Joined: 10 Sep 2008 Online Status: Offline Posts: 25 |
Quote Reply
Posted: 04 Dec 2008 at 9:42am |
I successfully changed over 100 channels via the bulk channel editor with 1.0.32. Running Vista. |
|
|
|
|
MrChristmas2000
Beta Testers
Joined: 06 May 2008 Location: Georgia Online Status: Offline Posts: 344 |
Quote Reply
Posted: 04 Dec 2008 at 1:13pm |
|
Running XP.
I just tried it again this afternoon.
Edited 4 channels, clicked save with the following error.
Aurora Sequencer has encountered a problem and needs to close. We are sorry for the inconvenience.
If you were in the middle of something, the information you were working on might be lost.
For more information about this error, click here.
Error signature.
AppName: aurora)sequencer.exe AppVer. 1.0.0.32. ModName: ntdll.dll
ModVer: 5.1.26000.5512 Offset: 00002caf. |
|
|
Holding breath for DMX. |
|
|
|
|
Post Reply
|
Page <12345> |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options