Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0 > Bug Reports
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

changing ramp style

 Post Reply Post Reply Page  12>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
onewish1 View Drop Down
Newbie
Newbie


Joined: 09 Sep 2009
Online Status: Offline
Posts: 34
  Quote onewish1 Quote  Post ReplyReply Direct Link To This Post Topic: changing ramp style
    Posted: 14 Oct 2009 at 10:23am
ok here is one for you experts... I did a sequence myself from scratch... added shimmer ramp downs... save.. close the file.. open it again... and the shimmer ramps changed to regular ramp downs.. happened twice now.. thought I was crazy the first time
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 11:43am
I'll test this.  What percentages were you ramping from/to (e.g. 100% to 0%)?

Are these regular shimmer ramps, or are they RGB shimmer ramps?

Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 12:00pm
Would it also matter what type of controller you had it set to?  Ie, needs to be firmware 1.13+?
Back to Top
onewish1 View Drop Down
Newbie
Newbie


Joined: 09 Sep 2009
Online Status: Offline
Posts: 34
  Quote onewish1 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 12:15pm
regular shimmer ramps 100 - 0... not sure how to check the firmware.. sorry
Back to Top
onewish1 View Drop Down
Newbie
Newbie


Joined: 09 Sep 2009
Online Status: Offline
Posts: 34
  Quote onewish1 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 12:17pm
after putting them back in twice it is fine... just very annoying
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 2:28pm
I think what Dewey was asking was what device type you have the channel set to when you pull up the channel properties dialog for for the channel?

This setting needs to match the type of controller you are using.  If it does not, then the effect will be re-rendered into something that the device type can support (the "generic" types and pre-1.13 D-Light do not support shimmer ramp for example).
Back to Top
onewish1 View Drop Down
Newbie
Newbie


Joined: 09 Sep 2009
Online Status: Offline
Posts: 34
  Quote onewish1 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 4:49pm
oh thank you... it is D-Light ACx16 the controller I have
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993
  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 5:46pm
Onewish,

What they are referring to is what version of Firmware is present on the ACx16. It can be the older 1.12 (no ramping shimmer supported) or 1.13+ where ramping shimmer is supported. Only way to determine this is to use the D-Light hardware utility.

Also, there are three ACx16 choices in Aurora. One for pre-1.13, one for post 1.13 (just called ACx16), and one for RGB. Make certain the correct one is selected.

All the Best!

Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 9:03pm
I was talking about what controller type is set in the sequence itself (the editor won't know what you actually have hooked up to the network - and if you try to issue a ramping shimmer to an older version of the firmware, it would likely ignore the command or just give a regular shimmer).  Right click on one of the channel labels and go to channel properties to see what the controller type is set to. 

When sequencing, setting a ramping shimmer to a channel on a ACx16 pre 1.13 controlller should issue a warning - I was thinking that it might not hurt to ensure that it is not set on this older type.
Back to Top
onewish1 View Drop Down
Newbie
Newbie


Joined: 09 Sep 2009
Online Status: Offline
Posts: 34
  Quote onewish1 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Oct 2009 at 9:16pm
ok the d-light driver is 1.14... and my channels are set to ACx16
Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.329 seconds.