Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Upcoming Releases

 Post Reply Post Reply Page  <123>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341
  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 19 Feb 2010 at 8:07am
Originally posted by Pony_God

Any word on sticking channels


is this an Aurora issue or a hardware issue?
Chris

www.lightsonsixth.com
Back to Top
Jonathan View Drop Down
Beta Testers
Beta Testers


Joined: 07 Sep 2008
Location: SoCal
Online Status: Offline
Posts: 1237
  Quote Jonathan Quote  Post ReplyReply Direct Link To This Post Posted: 19 Feb 2010 at 1:37pm
Didn't we trace that problem back to the FTDI driver?  I'm pretty sure not an Aurora issue.
~Jonathan
Back to Top
Pony_God View Drop Down
Senior Member
Senior Member
Avatar

Joined: 01 Sep 2008
Location: Naples, FL
Online Status: Offline
Posts: 551
  Quote Pony_God Quote  Post ReplyReply Direct Link To This Post Posted: 19 Feb 2010 at 1:48pm
I didn't think so... I was running the latest driver and V3 of the adapter.
As for Aurora or hardware, It's not hardware unless it's tha adapter since... Well, three things.
1. Looping the sequencer drops the net after the first loop.
2. I've had an entire network not kick in until a few commands later at the start of the show/sequence.
3. There are a TON more sticking channels vs. last year and on the same with only the RS485 and Aurora being different.
 
If you check out this year's THX Intro, you'll see that the left side of the house doesn't kick in until the second command. As for stuck channels, I'd have to review the videos to point out a specific song/time where it's obvious.
Fine. You're so smart you rig up the lights.
D-Light users Unite!
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 19 Feb 2010 at 3:11pm
Sticking channels were tracked to two issues:

1. Some D-Light firmware versions are known to cause channels to stick.

2. There are some bad versions of the FTDI drivers out there (Windows Update pushed at least one of them).  In addition to sticky channels, bad drivers can also cause severe lag and/or loss of networks (there appears to be a race condition within some driver versions where the adapter can be both closing and opening simultaneously and as a result neither happens).  The issue is only compounded by changes FTDI made to their driver for Windows 7 compatibility which have caused a performance hit in the XP/Vista world.

Sticking channels and dropping networks are not an Aurora issue. 

Testing to determine which driver version is the correct one for Aurora is still pending (lots of system/adapter version combinations to test).

Back to Top
Comporder1 View Drop Down
DMX
DMX


Joined: 11 Dec 2007
Location: Brookhaven, MS
Online Status: Offline
Posts: 163
  Quote Comporder1 Quote  Post ReplyReply Direct Link To This Post Posted: 19 Feb 2010 at 4:25pm
FYI.... Dropped networks have also been caused by EMI near the adapter or network/USB cabling. I've had my radio tx lock up my USB485 adapter. Someone else found a motor near his cabling caused his adapter to lock up.
Back to Top
BigDPS View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 13 Dec 2007
Online Status: Offline
Posts: 471
  Quote BigDPS Quote  Post ReplyReply Direct Link To This Post Posted: 19 Feb 2010 at 6:18pm
Well all these changes will be very welcomed to this sequencer. Not having my wife hit me in the middle of the night and wake me up to inform me that our display has turned on again will be a blessing as well.Clap

Back to Top
JohnnyL View Drop Down
Pre-Order User
Pre-Order User
Avatar

Joined: 17 Dec 2007
Location: Merced Ca
Online Status: Offline
Posts: 67
  Quote JohnnyL Quote  Post ReplyReply Direct Link To This Post Posted: 26 Feb 2010 at 10:16am
I just wanted to say thanks for looking into the RGB & scheduler issues. John
"In God We Trust" all others pay cash
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 02 Apr 2010 at 12:22pm
Just updating this thread since the release obviously didn't happen in late March...

The delay is because we are fixing issues with the installer for version 1.1.  Testing has shown that all of the "uninstall/reinstall/reboot a dozen times" problems from the past several versions were about to blow up on us again with the 1.1 installation.  Switching installers wasn't part of the 1.1 schedule, so it has set us back a couple weeks.
Back to Top
BigDPS View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 13 Dec 2007
Online Status: Offline
Posts: 471
  Quote BigDPS Quote  Post ReplyReply Direct Link To This Post Posted: 21 Apr 2010 at 6:07pm
Will this update fix the importing of channels? It seems each time I import channels from a previously sequenced song, it will take an eternity and finally crash on me without doing what's supposed to happen.

Unless I'm not doing it right which could well be a possibility.Smile

Back to Top
bdkeen View Drop Down
Beta Testers
Beta Testers


Joined: 31 Dec 2007
Location: Easton,PA
Online Status: Offline
Posts: 380
  Quote bdkeen Quote  Post ReplyReply Direct Link To This Post Posted: 28 Apr 2010 at 12:06pm
Now in late April.. Do you believe this slippage in 1.1 will also result in 1.2 being delayed? My interest is in the DMX version (1.2)..
 
For me it's understandable to have delays, I'd much sooner see more of the bugs out of a release version. This post is purely driven by curiosity.
Back to Top
 Post Reply Post Reply Page  <123>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.250 seconds.