Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

ACx16 Hook up to Aurora

 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
vista598 View Drop Down
Newbie
Newbie
Avatar

Joined: 20 Aug 2008
Location: Brunswick,,GA
Online Status: Offline
Posts: 4
  Quote vista598 Quote  Post ReplyReply Direct Link To This Post Topic: ACx16 Hook up to Aurora
    Posted: 06 Dec 2008 at 12:20pm
I have my sequence and I have run the hardware utility on my ACx16. But when I close the utility, the light on the controller starts blinking again and Aurora does not seem to see the controller as nothing happens when I play the sequence. Any help would be greatly appreciated.
Valhalla
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993
  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 06 Dec 2008 at 1:16pm
Is Aurora configured for the proper COM port, and Network #?

Is the sequence configured to play to a valid controller ID?

Back to Top
vista598 View Drop Down
Newbie
Newbie
Avatar

Joined: 20 Aug 2008
Location: Brunswick,,GA
Online Status: Offline
Posts: 4
  Quote vista598 Quote  Post ReplyReply Direct Link To This Post Posted: 06 Dec 2008 at 1:20pm
I have it configured to com5 and network 1. Testing it through the Hardware Utility it works fine so the hook up to the computer is good. Each channel is configured to network 1, controller 3 (which is the assigned controller number I used). should the light be bliking when I access Aurora?
Valhalla
Back to Top
Jonathan View Drop Down
Beta Testers
Beta Testers


Joined: 07 Sep 2008
Location: SoCal
Online Status: Offline
Posts: 1237
  Quote Jonathan Quote  Post ReplyReply Direct Link To This Post Posted: 06 Dec 2008 at 1:20pm
Correct, the ACx16 "heart beat" blinks when communication isn't present.  To send commands out, click on the light bulb icon.  Aurora won't automatically connect to the controller when it is opened.  When the light bulb is red, your commands will be sent out.


Edited by Jonathan - 06 Dec 2008 at 1:23pm
~Jonathan
Back to Top
vista598 View Drop Down
Newbie
Newbie
Avatar

Joined: 20 Aug 2008
Location: Brunswick,,GA
Online Status: Offline
Posts: 4
  Quote vista598 Quote  Post ReplyReply Direct Link To This Post Posted: 06 Dec 2008 at 1:41pm
Jonathan, it works!!! thanks so much. I really appreciate the help. Being a newbie and without an instruction manual it's a little difficult to figure some of this out.
Valhalla
Back to Top
Jonathan View Drop Down
Beta Testers
Beta Testers


Joined: 07 Sep 2008
Location: SoCal
Online Status: Offline
Posts: 1237
  Quote Jonathan Quote  Post ReplyReply Direct Link To This Post Posted: 06 Dec 2008 at 1:49pm
Video tutorial by Flanigan:  Part one, and part two.  A little bit dated now that there's been a few additions to Aurora, but it will get you started. 

A manual is in the works, but despite the "week or two" message that's been there for months, I doubt it will be ready anytime soon as there are more pressing issues to tend to.  If you have any other questions, feel free to ask here.  We're always more than willing to offer a hand.  
~Jonathan
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.215 seconds.