lights to controller
Printed From: Aurora
Category: Aurora Sequencer Software
Forum Name: Aurora 1.0
Forum Discription: This is the place to discuss (and report bugs) the 1.0 version of Aurora
URL: http://www.aurorashow.com/forum/forum_posts.asp?TID=481
Printed Date: 04 Nov 2025 at 4:51am
Software Version: Web Wiz Forums 9.06 - http://www.webwizforums.com
Topic: lights to controller
Posted By: jtcfrank7
Subject: lights to controller
Date Posted: 11 Nov 2008 at 8:00pm
|
having trouble gettting a command to go to controller everything else seems to be working fine i think missing something but dont what any help would be great thank you john ------------- jtcfrank7 |
Replies:
Posted By: kennyz06
Date Posted: 11 Nov 2008 at 8:16pm
|
Check your com port setting in aurora, and click the light bulb to send output to the controller... ------------- http://www.McKinneyChristmas.com - http://www.McKinneyChristmas.com 
|
Posted By: ChrisL1976
Date Posted: 11 Nov 2008 at 8:20pm
|
make sure Hardware utility is not connected to your controllers
------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 11 Nov 2008 at 8:21pm
|
com port is set when i click light bulb nothing happens john ------------- jtcfrank7 |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 7:02am
|
hardware utility shut off,still no lights. do i need to have all channels set up?also what do i do for channel device thanks john ------------- jtcfrank7 |
Posted By: mramsey
Date Posted: 12 Nov 2008 at 8:10am
|
I made this mistake, does the controller ID# match the ID# that is assigned to the controller in Aurora. Check under bulk editor If the unit ID is set at 2 then when you check the bulk editor the ID should match Hope this helps If you have the HW utility open can you turn the lights on ?? ------------- http://www.d-light.us"> 
|
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 8:16am
|
both ids are the same yes i can operate lights through hardware ------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:18am
|
Forgive the basic descriptions if you already know this information. Use your hardware utility program to determine which device number your controller is on. This is done through the Discover tab on D-lights hardware utility (I'm sure LOR has something similar if your using LOR controllers) Open HWU, Connect to the controller, the flashing red lights will go solid, and open the discover tab and click Discover. It will come up with a number on the left side. The default is 2 if you have never changed it. Once you know that number, you have to change the device number on your channels in aurora to match that number. The device number for your channels must match the device number set in the controller. This is how you can use multiple controllers. You change the controller Device number to match your Aurora device number. I have 4 controllers numbered 1-4. That way each group of 16 channels has a different address. The device number is the address. ------------- Chris www.lightsonsixth.com |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:21am
|
DO you have the right controller type set in Aurora? D-light, LOR, etc. When turn on the light bulb and click play, is the blinking light going solid? ------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 9:17am
|
controller type is configured in settings light does go solid i believe i dont have each channel matched with controller ill try that and see what happens thanks for help john ------------- jtcfrank7 |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 5:52pm
|
i want to thank all that helped ( or tried ) but still have same problem cannot get lights to play thanks again john ------------- jtcfrank7 |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 6:34pm
 
------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 7:46pm
|
ok. lets make sure you have everything set right. 1. Under setting---serial network configuration---you clicked ADD Network. In that window you chose network 1 and the correct Com port and then clicked add. You should see the network listed.....Network 1, comport #, Data Rate 56000? 2. All your channels are configured to the SAME device number as your controller? 3. You have lights commands on your sequence? 4. You pressed the light bulb? 5. You hit play and the light on the controller went solid right before the music started? 6. Music played? |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 7:53pm
|
yes yes yes yes yes yes yes what else is there? john thanks for helping me out chris ------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:20pm
|
who makes the board? d-light or LOR?
------------- Chris www.lightsonsixth.com |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:44pm
|
what is the baud rate on the board set to?
------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 8:46pm
|
d light
------------- jtcfrank7 |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 8:47pm
------------- jtcfrank7 |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 8:49pm
|
auto ------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:54pm
|
Yes, its Baud rate on the HWU-----same thing though ------------- Chris www.lightsonsixth.com |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:56pm
well I'm stumped....
------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 8:56pm
------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 8:57pm
|
no...I've run test sequences with 1 or 2
------------- Chris www.lightsonsixth.com |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 9:00pm
|
try creating a new sequence and load a entire controller....throw in a few event marks and some on commands and try it out.
------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 9:00pm
|
well whats got me stump is everything runs through the visualizer
------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 9:04pm
|
if something isn't set up right.....visualizer will still work...you dont have to have a controller linked to the computer for Visualizer to work.
------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 9:05pm
|
let me ask a dumb question,just so i know if im doing this right,how do you set a command ------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 9:15pm
|
command.....(intensity, ramp, shimmer, twinkle, etc.) on your sequence, your going to set event markers using the clock with the arrow button...(or press V) go under your wave form and somewhere left click....that will leave a vertical line. then move to the right and add another. Then click the I button and click a space next to your channels you have made. This should leave a solid mark. These are what tell your lights to turn on and off and at what exact time. ------------- Chris www.lightsonsixth.com |
Posted By: jtcfrank7
Date Posted: 12 Nov 2008 at 9:26pm
|
does the hardware need to be off when playing? ------------- jtcfrank7 |
Posted By: ChrisL1976
Date Posted: 12 Nov 2008 at 9:51pm
|
YES......Make sure you are not connected.....it will not work if HWU is linked to the controller
------------- Chris www.lightsonsixth.com |
Posted By: LightsOnLogan
Date Posted: 12 Nov 2008 at 10:24pm
|
If you attempt to run Aurora at the same time the HWU is running Aurora will not be able to use the port (because it is already in use by the HWU). If you attempt both at once, there is also a chance that Aurora will also lose access to the port until after a reboot. ------------- http://www.aurorashow.com/"> 
|