Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

After moving everything lights don't work

 Post Reply Post Reply Page  123>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
garrisonl View Drop Down
Newbie
Newbie
Avatar

Joined: 02 Sep 2008
Location: Houston, TX
Online Status: Offline
Posts: 38
  Quote garrisonl Quote  Post ReplyReply Direct Link To This Post Topic: After moving everything lights don't work
    Posted: 09 Sep 2008 at 12:38pm
Hey guys:
Don't know which category this falls under either.  Got all my sequesnces moved to Aurora.  When I ran the test from the AC16 the lights work.  When I start the music they don't.  Did the com port just like in spectrum.  What am I missing to make them work?
Mark & Lisa Garrison
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993
  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 12:48pm
Check your controller addressing and be certain they are all set to Network Segment 1, and that your Serial Network Config is also set for Network 1.

Back to Top
garrisonl View Drop Down
Newbie
Newbie
Avatar

Joined: 02 Sep 2008
Location: Houston, TX
Online Status: Offline
Posts: 38
  Quote garrisonl Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 1:00pm
Giving me
Debugging information
8005: port already open
lightbulb tool
mscomm
 
Still no lights
Mark & Lisa Garrison
Back to Top
garrisonl View Drop Down
Newbie
Newbie
Avatar

Joined: 02 Sep 2008
Location: Houston, TX
Online Status: Offline
Posts: 38
  Quote garrisonl Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 1:48pm
Give up time
Neither aurora or spectrum work now.Confused Maybe tomorrow will be a better day.
Mark & Lisa Garrison
Back to Top
JonB256 View Drop Down
DMX
DMX
Avatar

Joined: 19 Dec 2007
Location: Granbury, TX
Online Status: Offline
Posts: 130
  Quote JonB256 Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2008 at 4:49pm
Are you simultaneously running a Hardware Controller? (LOR or D-Light)
Are you running the sequencer at the same time?
JonB - D-Light user
Back to Top
garrisonl View Drop Down
Newbie
Newbie
Avatar

Joined: 02 Sep 2008
Location: Houston, TX
Online Status: Offline
Posts: 38
  Quote garrisonl Quote  Post ReplyReply Direct Link To This Post Posted: 10 Sep 2008 at 5:35am
No, I fixed it.  It was called reboot.  Amazing what happens when you turn a computer off and then back on.Embarrassed
As always, Thx guys
Mark & Lisa Garrison
Back to Top
jberner View Drop Down
Groupie
Groupie
Avatar

Joined: 12 Sep 2008
Location: Ruther Glen, VA
Online Status: Offline
Posts: 85
  Quote jberner Quote  Post ReplyReply Direct Link To This Post Posted: 12 Sep 2008 at 1:45pm
I have a similar issue when I start a new sequence. It wouldn't display to the lights for anything. I had to save, close Aurora and then reopen it to get the lights to activate.

I have also noticed that when I have a sequences open, start a new one and import my channels from the previous one it also leaves the lights programmed to the old sequence even though they don't appear in the new sequence.  Even though the light programming is from the wrong show(the previous one) if you save it, it saves the proper data and if you close and reopen the software it begins with the proper (new) show data loaded.


Edited by jberner - 14 Sep 2008 at 7:22pm
Back to Top
garrisonl View Drop Down
Newbie
Newbie
Avatar

Joined: 02 Sep 2008
Location: Houston, TX
Online Status: Offline
Posts: 38
  Quote garrisonl Quote  Post ReplyReply Direct Link To This Post Posted: 20 Sep 2008 at 2:16pm
Ok got this computer up and running.  Now not sure what I'm doing wrong.  Does the Dlight hardware utility have to be running?  It discovers the controller, have everything set to 1 and com3 was assigned to the controller.  Test lights work fine, but no lights when i send it to the controller.  If I close the hardware utility, I have to reenter everything.  Any ideas guys?Confused
Mark & Lisa Garrison
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993
  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 20 Sep 2008 at 3:04pm
I would suspect that if the HWU was running the same time as Aurora was outputting there would be a communications conflict. The D-Light HWU is just an add-on for Aurora and has no bearing on Aurora's functions. If there is a problem using the D-Light HWU with a D-Light controller, then your best bet is the D-Light forums - although we'll try to help here too!
 
How about the Network number? Has that been assigned? You cannot assign a COM port to a controller, btw. Whatever the OS assigns (since windoze, mere humanz no longer have control in this regard) to the RS485 adaptor or WiLink is what the COM port will be.
 
Test lights??Confused Please explain. 

Back to Top
garrisonl View Drop Down
Newbie
Newbie
Avatar

Joined: 02 Sep 2008
Location: Houston, TX
Online Status: Offline
Posts: 38
  Quote garrisonl Quote  Post ReplyReply Direct Link To This Post Posted: 20 Sep 2008 at 3:43pm
Sorry, there is a test button on the controller and when I push it it works.  But when i send the music to the controller is does not.  I will keep trying.  I thought it had something to do with the software.  Thx, I will ask Darryl or one of the guys over there.  They have pretty much run me through all of this.
Mark & Lisa Garrison
Back to Top
 Post Reply Post Reply Page  123>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.609 seconds.