Aurora Homepage
Main Hardware Software Cables/Adapters Forum Contact
Forum Home Forum Home > The Vault > I'm New From Spectrum And I Need Help!
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Forum LockedDesperate for Guidance!
 Post Reply Post Reply Page  <12
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Bigindian View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 13 Oct 2007
Online Status: Offline
Posts: 373 		  Quote Bigindian Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 8:10pm
As wierd as this may sound, I helped someone out last year with almost the same symptoms as you have illustrated above. 
 
Are you absolutely sure that you are not using a cat 5 crossover cable?  Does it work as a normal cable for a computer network?
 
Try swapping the cable and report back.  We tried everything you did above and have no success for hours.  Swapped the cable and all was well
 
Cheers
 
Back to Top
jswear View Drop Down
Newbie
Newbie


Joined: 18 Oct 2008
Online Status: Offline
Posts: 6 		  Quote jswear Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2008 at 6:48am
Thanks Chris!
 
How exactly do I "... shoot this one over to Darryl..." at D-Light?
I've posted the same message on the D-Light forum, does that count?
 
Thanks for all of your help.
JC
Back to Top
jswear View Drop Down
Newbie
Newbie


Joined: 18 Oct 2008
Online Status: Offline
Posts: 6 		  Quote jswear Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2008 at 6:51am

Yes, I was clicking "Connect" as I tied each of the ports but still no discovery.

Thanks,

JC
Back to Top
jswear View Drop Down
Newbie
Newbie


Joined: 18 Oct 2008
Online Status: Offline
Posts: 6 		  Quote jswear Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2008 at 7:21am
Thanks JonB,
 
I tried as directed and still no luck.
 
I connected one controller.
Launched the Firmware Updater, set the port to COM5, Tried connecting to the various ID numbers but timed out each time.
Tried the FORCE command and this also timed out.
 
Best,
JC
Back to Top
bdkeen View Drop Down
Beta Testers
Beta Testers


Joined: 31 Dec 2007
Location: Easton,PA
Online Status: Offline
Posts: 380 		  Quote bdkeen Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2008 at 7:55am
Just a thought but have you tried changing the COM port number at all to see if things get detected on a different COM #..  Don't remember the exact problem I had once but when I changed computers I had some sort of a problem.  I switched to COM 4 for the USB serial port and everything worked fine.  Over the years I've seen some strange things happen with higher number com ports and the interrupts they use so I usually try to avoid using anything over 4 if I can.
 
If you're not already using com 3 or 4 you might try - I would think that it can't be any worse than it already is and you can always switch back to the current com port configuration.
 
The red led in the controller should go solid - not blinking - when communications is established. 
 
May also want to check com port settings - baud rate, data bits, parity, stop bits, flow control.
 
Default settings should be 9600, 8, none, 1, none


Edited by bdkeen - 26 Oct 2008 at 8:01am
Back to Top
peteandvanessa View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 11 Dec 2007
Location: Rocklin, CA
Online Status: Offline
Posts: 206 		  Quote peteandvanessa Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2008 at 10:03am
I remember some time ago (last year), I could connect to my controllers and run sequences etc etc. I could NEVER discover a particular controller.
 
It's been sometime, but I think I updated the Firmware and then I changed the  baud rate comms speed when comnecting to the controller.
 
Here's how I did it:
 
To get the H/W utility to discover the board do this:


Open the H/W utility, select edit and select "Enable Baud rate changes", then I connected to the board using the H/W utility, then I went to the general config tab and "dragged the Baud rate" to "Auto" and hit set. (note all boards in your set up will need to have the same baud rate)

I then disconnected, opened up the firmware updater and updated the firmware to the latest firmware. After than I went back to the H/W utility and I could finally discover all my controllers.
 
Here's the original thread on the D-Light board:
 
 


Edited by peteandvanessa - 26 Oct 2008 at 10:21am
Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341 		  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2008 at 10:39am
Originally posted by jswear

Thanks Chris!
 
How exactly do I "... shoot this one over to Darryl..." at D-Light?
I've posted the same message on the D-Light forum, does that count?
 
Thanks for all of your help.
JC


go over to D-lights website and top right of the screen, there is a Contact Us button....you can send him a email from there. 
Chris

www.lightsonsixth.com
Back to Top
 Post Reply Post Reply Page  <12

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.672 seconds.